xDSL.at

Habe hier ein ST 510 v4 1 port POTS welches mittels aonModemkonfigurator auf Single Mode konfiguriert wurde.

Leider wird das ST 510 nicht syncron das @ led blickt nur in 3-4 Mal dann ist wieder Finster Pause!

Woran kanns liegen? Mit dem 546 klappt es.

User.ini anbei!


Danke!!!

Code: Alles auswählen

[ env.ini ]
set var=CONF_REGION value="tr(1,Austria)"
set var=CONF_PROVIDER value="tr(2,Internet Service Provider)"
set var=CONF_DESCRIPTION value="tr(3,Austria [11/03])"
set var=CONF_SERVICE value="tr(4,Broadband Access)"
set var=CONF_DATE value="tr(5,2003 November)"
set var=CONF_VERSION value="4.2.3.0.0"
set var=CONF_TPVERSION value=1.2.0
set var=UPGRADE_URL value="http://www.speedtouch.com/upgrade500.htm"
set var=HOST_SETUP value=none
set var=SESSIONTIMEOUT value=60
set var=%PPP1_username value="tr(6,username)"
set var=%PPP1_pwd value="tr(7,password)"

[ config.ini ]

[ hostwizard.ini ]
includefile name="aq4230de.lng"

[ wizard.ini ]
config autopopup=no allow_factory_tpl=no trace=yes

[ adslpots.ini ]
config opermode=multimode maxbitspertoneUS=14 trace=on modemoption=00000000000000000000000000000000

[ adslisdn.ini ]
config opermode=multimode maxbitspertoneUS=14 trace=on modemoption=00000000000000000000000000000000 extendedBWmode=0

[ shdsl.ini ]

[ oam.ini ]
config clp=1 loopbackid=6a6a6a6a6a6a6a6a6a6a6a6a6a6a6a6a
mode port=dsl0 blocking=enabled
mode port=dsl1 blocking=enabled
mode port=atm2 blocking=enabled
mode port=atm3 blocking=enabled
mode port=atm5 blocking=enabled
mode port=aal5 blocking=enabled

[ qos.ini ]
config format=bytes
add name="default" class=ubr tx_peakrate=27785 rx_peakrate=27785 framediscard=enabled dynamic=no

[ autopvc.ini ]
config mode=active type=bridge opmode=partial overwrite=disabled peakrate=0

[ eth.ini ]
ifconfig intf=1 type=auto
config intf=1 state=enabled

[ switch.ini ]

[ system.ini ]
config mdap=enabled
config upnp=enabled
config drst=enabled
config ddm=disabled
config dcache=enabled
config strictusername=enabled
config digestauth=enabled
settime timezone=+00:00 daylightsaving=no

[ config.ini ]

[ diagnostics.ini ]
config pingtimeout=1000 pingpacketsize=20

[ snmp.ini ]
config RWCommunity=private ROCommunity=public
config sysContact="Internet Service Provider"
config sysName="Speedtouch 510"
config sysLocation="Austria"

[ syslog.ini ]

[ upnp.ini ]
config maxage=1800 defcservice=DIALUP_PPP1 writemode=full safenat=enabled

[ nat.ini ]
bind application=SIP port=5060
bind application=GRE port=1
bind application=PPTP port=1723
bind application=ESP port=1
bind application=IKE port=ike
bind application=ILS port=ldap
bind application=ILS port=ils
bind application=H323 port=h323
bind application=FTP port=ftp
bind application=RTSP port=rtsp
bind application=RAUDIO(PNA) port=realaudio
bind application=IP6TO4 port=1
bind application=IRC port=6660 port_end=6670
config timeout_ICMP=00:01
config timeout_UDP=00:05
config timeout_TCP=00:15
config timeout_TCP_nego=00:01
config timeout_other=00:01
config ike_port=floated

[ phone.ini ]
add name=Br1 addr=8.35 type=ethoa dynamic=no
add name=Br2 addr=8.36 type=ethoa dynamic=no
add name=Br3 addr=8.37 type=ethoa dynamic=no
add name=Br4 addr=8.38 type=ethoa dynamic=no
add name=RELAY_PPP1 addr=8.48 type=pppoa dynamic=no
add name=RELAY_PPP2 addr=8.49 type=pppoa dynamic=no
add name=RELAY_PPP3 addr=8.50 type=pppoa dynamic=no
add name=RELAY_PPP4 addr=8.51 type=pppoa dynamic=no
add name=DIALUP_PPP1 addr=8.64 type=pppoa dynamic=no

[ bridge.ini ]
ifadd intf=Br1 dest=Br1
ifconfig intf=Br1 encaps=llc/snap portstate=forwarding
ifattach intf=Br1
ifadd intf=Br2 dest=Br2
ifconfig intf=Br2 encaps=llc/snap portstate=forwarding
ifattach intf=Br2
ifadd intf=Br3 dest=Br3
ifconfig intf=Br3 encaps=llc/snap portstate=forwarding
ifattach intf=Br3
ifadd intf=Br4 dest=Br4
ifconfig intf=Br4 encaps=llc/snap portstate=forwarding
ifattach intf=Br4
config age=300 filter=no_WAN_broadcast

[ ethoa.ini ]

[ pppoerelay.ini ]
add port=eth0

[ pppoe.ini ]

[ pptp.ini ]
profadd name="default" encaps=vcmux

[ pppoa.ini ]
ifadd intf=DIALUP_PPP1
rtadd intf=DIALUP_PPP1 dst=0.0.0.0 dstmsk=0 src=0.0.0.0 srcmsk=0 metric=1
ifconfig intf=DIALUP_PPP1 dest=DIALUP_PPP1 encaps=vcmux
ifconfig intf=DIALUP_PPP1 qos=default
ifconfig intf=DIALUP_PPP1 pcomp=on accomp=on passive=off silent=off echo=on
ifconfig intf=DIALUP_PPP1 restart=on demanddial=on
ifconfig intf=DIALUP_PPP1 retryinterval=3
ifconfig intf=DIALUP_PPP1 idle=60 idletrigger=TX
ifconfig intf=DIALUP_PPP1 user=$%PPP1_username password=$%PPP1_pwd savepwd=on
ifconfig intf=DIALUP_PPP1 addrtrans=pat
ifconfig intf=DIALUP_PPP1 trace=on
ifconfig intf=DIALUP_PPP1 status=down

[ ipoa.ini ]

[ cip.ini ]

[ autoip.ini ]

[ ip.ini ]
config forwarding=on firewalling=on redirects=off sourcerouting=off netbroadcasts=off ttl=64 fraglimit=64 defragmode=nat addrcheck=dynamic mssclamping=on
apadd addr=10.0.0.138/24 intf=eth0 addroute=no
ifconfig intf=loop mtu=1500 group=local linksensing=on
ifconfig intf=eth0 mtu=1500 group=lan linksensing=on
ifconfig intf=DIALUP_PPP1 mtu=1500 status=down group=wan linksensing=on
rtadd dst=0.0.0.0/0 intf=eth0 metric=70
rtadd dst=224.0.0.0/4 intf=eth0 metric=0
rtadd dst=10.0.0.0/24 gateway=10.0.0.138 metric=0
rtadd dst=255.255.255.255/32 gateway=10.0.0.138 metric=0
rtadd dst=10.0.0.0/24 src=10.0.0.0/24 gateway=10.0.0.138 metric=0

[ label.ini ]
chain create chain=user_labels

[ pfilter.ini ]

[ pfirewall.ini ]
chain create chain=source
chain create chain=sink
chain create chain=forward
rule create chain=sink index=0 srcintfgrp=!wan action=accept
rule create chain=sink index=1 prot=icmp icmptype=echo-reply action=accept
rule create chain=sink index=2 prot=icmp icmptype=destination-unreachable action=accept
rule create chain=sink index=3 prot=icmp icmptype=time-exceeded action=accept
rule create chain=sink index=4 prot=udp dstport=dns action=accept
rule create chain=sink index=5 prot=udp dstport=bootpc action=accept
rule create chain=sink index=6 prot=udp dstport=snmp log=yes action=count
rule create chain=sink index=7 action=drop
rule create chain=source index=0 dstintfgrp=!wan action=accept
rule create chain=source index=1 prot=icmp icmptype=echo-request action=accept
rule create chain=source index=2 prot=udp dstport=dns action=accept
rule create chain=source index=3 prot=udp dstport=bootps action=accept
rule create chain=source index=4 prot=udp srcport=snmp log=yes action=count
rule create chain=source index=5 action=drop
rule create chain=forward index=0 srcintfgrp=wan dstintfgrp=wan action=drop
assign  hook=sink chain=sink
assign  hook=forward chain=forward
assign  hook=source chain=source

[ dhcp.ini ]
config autodhcp=on scantime=20 state=enabled trace=on
policy verifyfirst=on trustclient=on
pool add name="LAN_private" index=0
pool config name=LAN_private intf=eth0 poolstart=10.0.0.1 poolend=10.0.0.254 netmask=24 gateway=10.0.0.138 server=10.0.0.138 leasetime=7200

[ dhcr.ini ]
ifconfig intf=eth0 relay=on
add addr=127.0.0.1 intf=eth0 giaddr=10.0.0.138

[ dnsd.ini ]
domain domain="lan"
add hostname="speedtouch"
start
troff

[ dhcc.ini ]
config trace=on
ifadd intf=eth0
ifconfig intf=eth0 addrtrans=none dns=on gateway=on metric=1 dnsmetric=1
ifattach intf=eth0

[ script.ini ]
add name=autopvc_add_qos index=0 command="qosbook add name _auto_$1_$2 class $3 tx_peakrate $4 tx_sustrate $5 tx_maxburst $6 rx_peakrate $4 rx_sustrate $5 rx_maxburst $6 dynamic yes"
add name=autopvc_delete_qos index=0 command="qosbook delete name _auto_$1_$2"
add name=autopvc_add_bridge index=0 command="qosbook add name _auto_$1_$2 class $3 tx_peakrate $4 tx_sustrate $5 tx_maxburst $6 rx_peakrate $4 rx_sustrate $5 rx_maxburst $6 dynamic yes"
add name=autopvc_add_bridge index=1 command="phonebook add name _auto_$1_$2 addr $1.$2 type any dynamic yes"
add name=autopvc_add_bridge index=2 command="bridge ifadd intf _auto_$1_$2 dest _auto_$1_$2"
add name=autopvc_add_bridge index=3 command="bridge ifconfig intf _auto_$1_$2 qos _auto_$1_$2"
add name=autopvc_add_bridge index=4 command="bridge ifattach intf _auto_$1_$2"
add name=autopvc_delete_bridge index=0 command="bridge ifdetach intf _auto_$1_$2"
add name=autopvc_delete_bridge index=1 command="bridge ifdelete intf _auto_$1_$2"
add name=autopvc_delete_bridge index=2 command="phonebook delete name _auto_$1_$2"
add name=autopvc_delete_bridge index=3 command="qosbook delete name _auto_$1_$2"
add name=autopvc_add_pppoerelay index=0 command="qosbook add name _auto_$1_$2 class $3 tx_peakrate $4 tx_sustrate $5 tx_maxburst $6 rx_peakrate $4 rx_sustrate $5 rx_maxburst $6 dynamic yes"
add name=autopvc_add_pppoerelay index=1 command="phonebook add name _auto_$1_$2 addr $1.$2 type any dynamic yes"
add name=autopvc_add_pppoerelay index=2 command="ethoa ifadd intf _auto_$1_$2 dest _auto_$1_$2"
add name=autopvc_add_pppoerelay index=3 command="ethoa ifconfig intf _auto_$1_$2 qos _auto_$1_$2"
add name=autopvc_add_pppoerelay index=4 command="ethoa ifattach intf _auto_$1_$2"
add name=autopvc_add_pppoerelay index=5 command="ip ifwait intf _auto_$1_$2 timeout 15 adminstatus up"
add name=autopvc_add_pppoerelay index=6 command="pppoe relay add port _auto_$1_$2"
add name=autopvc_delete_pppoerelay index=0 command="pppoe relay delete port _auto_$1_$2"
add name=autopvc_delete_pppoerelay index=1 command="ethoa ifdetach intf _auto_$1_$2"
add name=autopvc_delete_pppoerelay index=2 command="ethoa ifdelete intf _auto_$1_$2"
add name=autopvc_delete_pppoerelay index=3 command="phonebook delete name _auto_$1_$2"
add name=autopvc_delete_pppoerelay index=4 command="qosbook delete name _auto_$1_$2"
add name=autopvc_change_qos index=0 command="$$1 ifdetach intf $2"
add name=autopvc_change_qos index=1 command="$$1 ifconfig intf $2 qos $3"
add name=autopvc_change_qos index=2 command="$$1 ifattach intf $2"
add name=autopvc_change_qos_pppoerelay index=0 command="ethoa ifdetach intf $1"
add name=autopvc_change_qos_pppoerelay index=1 command="ethoa ifconfig intf $1 qos $2"
add name=autopvc_change_qos_pppoerelay index=2 command="ethoa ifattach intf $1"
add name=autopvc_change_qos_pppoerelay index=3 command="pppoe relay add port $1"
add name=autopvc_change_qos_pppoeethoa index=0 command="ethoa ifdetach intf $1"
add name=autopvc_change_qos_pppoeethoa index=1 command="ethoa ifconfig intf $1 qos $2"
add name=autopvc_change_qos_pppoeethoa index=2 command="ethoa ifattach intf $1"
add name=autopvc_change_qos_pppoeethoa index=3 command="pppoe ifattach intf $3"
add name=autopvc_change_qos_pppoa index=0 command="pppoa ifdetach intf $1"
add name=autopvc_change_qos_pppoa index=1 command="ip ifwait intf $1 timeout 5 adminstatus down"
add name=autopvc_change_qos_pppoa index=2 command="pppoa ifconfig intf $1 qos $2"
add name=autopvc_change_qos_pppoa index=3 command="pppoa ifattach intf $1"

[ language.ini ]
config language=en

langdef lang=de charset=ISO-8859-1
t r="1, Österreich"
t r="2, Internetdienstanbieter"
t r="3, Österreich [11/03]"
t r="4, Breitbandzugang"
t r="5, 2003 November"
t r="6, Benutzername"
t r="7, Kennwort"


[ endofarch ]


Und DIE user.ini ist tatsächlich VOM Modem und nicht von einer CD?

ja die hab ich mittels dem downgeloadeten aonModemkonfigurator ins
Modem gespielt.

Auf der Modem Seite steht immer: WARNING: Modemleitung ist unterbrochen

Warum?

Das war nicht meine Frage.
In der von Dir geposteten ist ein Abschnitt ADSLPOTS und ADSLISDN drin.
Nach dem Importieren ins Modem ist nur mehr der richtige Eintrag drin, der andere wird verworfen.
Wenn Du nun ein Backup der Konfig AUS DEM MODEM machst ist sichtbar, ob es ein POTS oder ISDN-Typ ist.

Das hat das Modem Backup ausgespuckt:

Code: Alles auswählen

[ language.ini ]
config language=de

[ script.ini ]
add name=autopvc_add_qos index=0 command="qosbook add name _auto_$1_$2 class $3 tx_peakrate $4 tx_sustrate $5 tx_maxburst $6 rx_peakrate $4 rx_sustrate $5 rx_maxburst $6 dynamic yes"
add name=autopvc_delete_qos index=0 command="qosbook delete name _auto_$1_$2"
add name=autopvc_add_bridge index=0 command="qosbook add name _auto_$1_$2 class $3 tx_peakrate $4 tx_sustrate $5 tx_maxburst $6 rx_peakrate $4 rx_sustrate $5 rx_maxburst $6 dynamic yes"
add name=autopvc_add_bridge index=1 command="phonebook add name _auto_$1_$2 addr $1.$2 type any dynamic yes"
add name=autopvc_add_bridge index=2 command="bridge ifadd intf _auto_$1_$2 dest _auto_$1_$2"
add name=autopvc_add_bridge index=3 command="bridge ifconfig intf _auto_$1_$2 qos _auto_$1_$2"
add name=autopvc_add_bridge index=4 command="bridge ifattach intf _auto_$1_$2"
add name=autopvc_delete_bridge index=0 command="bridge ifdetach intf _auto_$1_$2"
add name=autopvc_delete_bridge index=1 command="bridge ifdelete intf _auto_$1_$2"
add name=autopvc_delete_bridge index=2 command="phonebook delete name _auto_$1_$2"
add name=autopvc_delete_bridge index=3 command="qosbook delete name _auto_$1_$2"
add name=autopvc_add_pppoerelay index=0 command="qosbook add name _auto_$1_$2 class $3 tx_peakrate $4 tx_sustrate $5 tx_maxburst $6 rx_peakrate $4 rx_sustrate $5 rx_maxburst $6 dynamic yes"
add name=autopvc_add_pppoerelay index=1 command="phonebook add name _auto_$1_$2 addr $1.$2 type any dynamic yes"
add name=autopvc_add_pppoerelay index=2 command="ethoa ifadd intf _auto_$1_$2 dest _auto_$1_$2"
add name=autopvc_add_pppoerelay index=3 command="ethoa ifconfig intf _auto_$1_$2 qos _auto_$1_$2"
add name=autopvc_add_pppoerelay index=4 command="ethoa ifattach intf _auto_$1_$2"
add name=autopvc_add_pppoerelay index=5 command="ip ifwait intf _auto_$1_$2 timeout 15 adminstatus up"
add name=autopvc_add_pppoerelay index=6 command="pppoe relay add port _auto_$1_$2"
add name=autopvc_delete_pppoerelay index=0 command="pppoe relay delete port _auto_$1_$2"
add name=autopvc_delete_pppoerelay index=1 command="ethoa ifdetach intf _auto_$1_$2"
add name=autopvc_delete_pppoerelay index=2 command="ethoa ifdelete intf _auto_$1_$2"
add name=autopvc_delete_pppoerelay index=3 command="phonebook delete name _auto_$1_$2"
add name=autopvc_delete_pppoerelay index=4 command="qosbook delete name _auto_$1_$2"
add name=autopvc_change_qos index=0 command="$$1 ifdetach intf $2"
add name=autopvc_change_qos index=1 command="$$1 ifconfig intf $2 qos $3"
add name=autopvc_change_qos index=2 command="$$1 ifattach intf $2"
add name=autopvc_change_qos_pppoerelay index=0 command="ethoa ifdetach intf $1"
add name=autopvc_change_qos_pppoerelay index=1 command="ethoa ifconfig intf $1 qos $2"
add name=autopvc_change_qos_pppoerelay index=2 command="ethoa ifattach intf $1"
add name=autopvc_change_qos_pppoerelay index=3 command="pppoe relay add port $1"
add name=autopvc_change_qos_pppoeethoa index=0 command="ethoa ifdetach intf $1"
add name=autopvc_change_qos_pppoeethoa index=1 command="ethoa ifconfig intf $1 qos $2"
add name=autopvc_change_qos_pppoeethoa index=2 command="ethoa ifattach intf $1"
add name=autopvc_change_qos_pppoeethoa index=3 command="pppoe ifattach intf $3"
add name=autopvc_change_qos_pppoa index=0 command="pppoa ifdetach intf $1"
add name=autopvc_change_qos_pppoa index=1 command="ip ifwait intf $1 timeout 5 adminstatus down"
add name=autopvc_change_qos_pppoa index=2 command="pppoa ifconfig intf $1 qos $2"
add name=autopvc_change_qos_pppoa index=3 command="pppoa ifattach intf $1"

[ env.ini ]
set var=CONF_REGION value=Austria
set var=CONF_PROVIDER value="Internet Service Provider"
set var=CONF_DESCRIPTION value="Austria [11/03]"
set var=CONF_SERVICE value="Broadband Access"
set var=CONF_DATE value="2003 November"
set var=CONF_VERSION value=4.2.3.0.0
set var=CONF_TPVERSION value=1.2.0
set var=UPGRADE_URL value=http://www.speedtouch.com/upgrade500.htm
set var=HOST_SETUP value=none
set var=SESSIONTIMEOUT value=60

[ wizard.ini ]
config allow_factory_tpl=no trace=yes autopopup=no

[ snmp.ini ]
config RWCommunity=_DEV_2EF2659F0D4FCAA4 ROCommunity=_DEV_F3DFC011AD43214E sysContact="Internet Service Provider" sysName="Speedtouch 510" sysLocation=Austria

[ phone.ini ]
add name=Br1 addr=8*35 type=ethoa
add name=Br2 addr=8*36 type=ethoa
add name=Br3 addr=8*37 type=ethoa
add name=Br4 addr=8*38 type=ethoa
add name=RELAY_PPP1 addr=8*48 type=pppoa
add name=RELAY_PPP2 addr=8*49 type=pppoa
add name=RELAY_PPP3 addr=8*50 type=pppoa
add name=RELAY_PPP4 addr=8*51 type=pppoa
add name=DIALUP_PPP1 addr=8*64 type=pppoa

[ ipqos.ini ]
config dest=Br1
config dest=Br2
config dest=Br3
config dest=Br4
config dest=RELAY_PPP1
config dest=RELAY_PPP2
config dest=RELAY_PPP3
config dest=RELAY_PPP4
config dest=DIALUP_PPP1
queue config dest=Br1 queue=0
queue config dest=Br1 queue=1
queue config dest=Br1 queue=2
queue config dest=Br1 queue=3
queue config dest=Br2 queue=0
queue config dest=Br2 queue=1
queue config dest=Br2 queue=2
queue config dest=Br2 queue=3
queue config dest=Br3 queue=0
queue config dest=Br3 queue=1
queue config dest=Br3 queue=2
queue config dest=Br3 queue=3
queue config dest=Br4 queue=0
queue config dest=Br4 queue=1
queue config dest=Br4 queue=2
queue config dest=Br4 queue=3
queue config dest=RELAY_PPP1 queue=0
queue config dest=RELAY_PPP1 queue=1
queue config dest=RELAY_PPP1 queue=2
queue config dest=RELAY_PPP1 queue=3
queue config dest=RELAY_PPP2 queue=0
queue config dest=RELAY_PPP2 queue=1
queue config dest=RELAY_PPP2 queue=2
queue config dest=RELAY_PPP2 queue=3
queue config dest=RELAY_PPP3 queue=0
queue config dest=RELAY_PPP3 queue=1
queue config dest=RELAY_PPP3 queue=2
queue config dest=RELAY_PPP3 queue=3
queue config dest=RELAY_PPP4 queue=0
queue config dest=RELAY_PPP4 queue=1
queue config dest=RELAY_PPP4 queue=2
queue config dest=RELAY_PPP4 queue=3
queue config dest=DIALUP_PPP1 queue=0
queue config dest=DIALUP_PPP1 queue=1
queue config dest=DIALUP_PPP1 queue=2
queue config dest=DIALUP_PPP1 queue=3

[ qos.ini ]
config format=bytes
add name=default class=ubr tx_peakrate=27785 rx_peakrate=27785 framediscard=enabled

[ oam.ini ]
config clp=1 loopbackid=6a6a6a6a6a6a6a6a6a6a6a6a6a6a6a6a
mode port=dsl0 blocking=enabled
mode port=dsl1 blocking=enabled
mode port=atm2 blocking=enabled
mode port=atm3 blocking=enabled
mode port=aal5 blocking=enabled
mode port=atm5 blocking=enabled

[ pfirewall.ini ]
chain create chain=forward
chain create chain=sink
chain create chain=source
rule create chain=forward index=0 srcintfgrp=wan dstintfgrp=wan action=drop
rule create chain=sink index=0 srcintfgrp=!wan action=accept
rule create chain=sink index=1 prot=icmp icmptype=echo-reply action=accept
rule create chain=sink index=2 prot=icmp icmptype=destination-unreachable action=accept
rule create chain=sink index=3 prot=icmp icmptype=time-exceeded action=accept
rule create chain=sink index=4 prot=udp dstport=dns action=accept
rule create chain=sink index=5 prot=udp dstport=bootpc action=accept
rule create chain=sink index=6 prot=udp dstport=snmp log=yes action=count
rule create chain=sink index=7 action=drop
rule create chain=source index=0 dstintfgrp=!wan action=accept
rule create chain=source index=1 prot=icmp icmptype=echo-request action=accept
rule create chain=source index=2 prot=udp dstport=dns action=accept
rule create chain=source index=3 prot=udp dstport=bootps action=accept
rule create chain=source index=4 prot=udp srcport=snmp log=yes action=count
rule create chain=source index=5 action=drop
assign  hook=sink chain=sink
assign  hook=forward chain=forward
assign  hook=source chain=source

[ label.ini ]
chain create chain=user_labels

[ bridge.ini ]
ifadd intf=Br1 dest=Br1
ifconfig intf=Br1
ifattach intf=Br1
ifadd intf=Br2 dest=Br2
ifconfig intf=Br2
ifattach intf=Br2
ifadd intf=Br3 dest=Br3
ifconfig intf=Br3
ifattach intf=Br3
ifadd intf=Br4 dest=Br4
ifconfig intf=Br4
ifattach intf=Br4
config age=300 filter=no_WAN_broadcast

[ pptp.ini ]
profadd name=default

[ ethoa.ini ]

[ ipoa.ini ]

[ cip.ini ]

[ pppoerelay.ini ]
add port=eth0

[ dhcp.ini ]
config autodhcp=on scantime=20 state=enabled trace=on
policy verifyfirst=on trustclient=on
pool add name=LAN_private
pool config name=LAN_private intf=eth0 poolstart=10.0.0.1 poolend=10.0.0.254 netmask=24 gateway=10.0.0.138 server=10.0.0.138 leasetime=7200

[ pppoa.ini ]
ifadd intf=DIALUP_PPP1
rtadd intf=DIALUP_PPP1 dst=0.0.0.0/0 src=0.0.0.0/0 metric=1
ifconfig intf=DIALUP_PPP1 dest=DIALUP_PPP1 pcomp=on accomp=on trace=on retryinterval=3 demanddial=on dnsmetric=0 idle=60 idletrigger=Tx addrtrans=pat
ifconfig intf=DIALUP_PPP1 user=username password=_DEV_960BA8506ED65968

[ pppoe.ini ]

[ ip.ini ]
config forwarding=on firewalling=on redirects=off sourcerouting=off netbroadcasts=off ttl=64 fraglimit=64 defragmode=nat addrcheck=dynamic mssclamping=on
apadd addr=10.0.0.138/24 intf=eth0 addroute=no
ifconfig intf=loop mtu=1500 group=local linksensing=on
ifconfig intf=eth0 mtu=1500 group=lan linksensing=on
ifconfig intf=DIALUP_PPP1 mtu=1500 status=down group=wan linksensing=on
rtadd dst=255.255.255.255/32 gateway=10.0.0.138
rtadd dst=10.0.0.0/24 gateway=10.0.0.138
rtadd dst=224.0.0.0/4 intf=eth0
rtadd dst=0.0.0.0/0 intf=eth0 metric=70

[ autoip.ini ]

[ eth.ini ]
ifconfig intf=1 type=auto
config intf=1 state=enabled

[ diagnostics.ini ]
config pingtimeout=1000 pingpacketsize=20

[ dnsc.ini ]
config qrytout=5 interval=10 qryretry=3 attempt=-1 search=on connection=permanent
add addr=127.0.0.1 port=53

[ dnsd.ini ]
domain domain=lan
add hostname=speedtouch
start
troff

[ dhcr.ini ]
ifconfig intf=eth0 relay=on
add addr=127.0.0.1 intf=eth0 giaddr=10.0.0.138

[ dhcc.ini ]
config trace=on

[ adslpots.ini ]
config opermode=multimode maxbitspertoneUS=14 trace=on modemoption=00000000000000000000000000000000

[ nat.ini ]
bind application=ESP port=1
bind application=FTP port=ftp
bind application=GRE port=1
bind application=H323 port=h323
bind application=IKE port=ike
bind application=ILS port=ldap
bind application=ILS port=ils
bind application=IP6TO4 port=1
bind application=IRC port=6660 port_end=6670
bind application=PPTP port=1723
bind application=RAUDIO(PNA) port=realaudio
bind application=RTSP port=rtsp
bind application=SIP port=sip
config timeout_TCP_nego=0:1

[ autopvc.ini ]
config mode=active type=bridge opmode=partial overwrite=disabled peakrate=0

[ system.ini ]
config upnp=enabled mdap=enabled drst=enabled
config digestauth=enabled strictusername=enabled dcache=enabled

[ upnp.ini ]
config maxage=1800 defcservice=DIALUP_PPP1 writemode=full safenat=enabled

[ endofarch ]



//edited by jutta. bitte fuer lange listings das "code" tag verwenden. macht den thread viel uebersichtlicher. danke

Dann scheint das Modem defekt zu sein.
Kommt halt gelegentlich vor.

modemdefekt glaub i eher nit, kann natürlich sein..
nur so am rande: wie kommst zu 510er und 546er?? hast Isdn oder Pots? hast das entsprechend korrekte 510er?

ich nehm schon stark an, HW ist von TA, oder? für einen Standort oder mehrere?

bevor du 510er auf singleuser umgestellt hast, hats funktioniert???
der singleuser modus ist nämlich ansich eh standardeinstellung in der Originalfassung.

ich würd modem mal resetten, dann Verkabelung checken, dann lansettings korrekt auf die üblichen machen, über WI ist klar dass du die meldung bekommst "modemleitung" unterbrochen, dann setup mit der originalst-cd machen, natürlich geht auch das korrekte Ini.File vom Konfigurator.

wie hast versucht dann die internetverbindung herzustellen???
irgendwie musst du diese ja zumindest einmal herstellen, im singleusermodus gehts nur mittels einer korrekt erstellten vpnverbindung??

an der leitung liegts scheinbar nicht.

wahnsinn2000 hat mich auf eine idee gebracht: koennte es ev sein, dass nur das led defekt ist?

reagiert das modem auf ping?
kannst du ins web- oder telnet-interface?
was steht unter "systeminformation" oder "diagnose"?